Setup Card Displayer for GCB-99A
Setup Card Displayer for GCB-99A
Setup card is running the same as APP setting
Mobile APP Settings are the same as Settings box Settings.
Full File indication on tech Parameter is here :
More official Manual file on MYHOBBY GCB -99A Control box
Setup card displayer instructions Connect the setup card to the GCB-99Acontrol box with a special data cable, and turnonthepower supply of the control box.
There are four buttons on the setup card"+,-,ENT and ESC". Afterselecting the language with"+ ,-", press ENT to enter the setting menu.
1. Servo setting:
There are 14 servo jacks labelled AIL1, AIL2, ELE1, ELE2, THR1, THR2, RUD1, RUD2, FLAPI, FLAP2, AUX1, AUX2, AUX3, AUX4 respectively. Each servo can be individually set direction, neutral point, highand 4 low end point. full in manual..........
2. Navigation light setting:
The navigation light has 14 ports, divided into 7 independent groups, Labelled L1-L2, L3-L4, L5-L6, L7-L8, L9, L10-L12,L13-L14 respectively, theinternal current limit has been done, LED light can be directly connectedto the control box navigation light port, do not add current limitingresistance, otherwise affect the brightness. full in manual..........
3. Landing gear:
There are 7 landing gear related ports, namely EG(FR), EG(LF), EG(RG), DOOR(FR), DOOR(LF), DOOR(RG), STEER, corresponding to the nosegear, left gear, right gear, front door, left door, right door, front wheel steeringservo. When inserting the cable, please connect the cable accordingtothe corresponding jack to facilitate the setting (such as the front cabinDOOR servo must be plugged into the DOOR(FR) jack). Landing gear setting: full in manual..........
4. brake setting:
There are two ports labelled EB1 and EB2 for electric brake,insert twoelectric brake cable into the ports,be careful of”+”,”-” pale. The brakingforce setting range is "0%-100%", 100% is the maximumbraking force, which can be set by the user according to personal habits, and thebrakeis only effective when the landing gear is lowered.
5. Gyro setting:
The GCB-99A control box has a built-in gyro scope, which canprovidean enhanced stability mode for the aircraft, mainly enhance thewind 10 resistance of the aircraft in the air, and do not affect the control feel of the pilot. full in manual..........
6. System Settings
A. Select the signal source At present, the control box signal source supports PWMandSbus. PWM mode can be matched with any type of remote control, Sbus canonly be used for Futaba.
B. Throttle mixed control pitch The mixing control is set to solve the pitch attitude change causedbythe change of speed. It is recommended to use the mixedcontrol programming or conditional mode provided by the remote control.
C. Flap mixed control pitch It is also recommended to use the mixed control programmingorconditional mode provided by the remote control.
D. Save and write parameters a. Save parameters: All parameters of the control box are savedinthememory of setup card. b. Write parameters: Write related parameters saved in the memoryof setup card to the control box. This operation overwrites existingparameters in the control box. 12 Adjustment tip: Due to the complexity of the landing gear related settings, Set thelanding gear light and the door correctly before landing gear setting. Keep the landing gear in the retracted position during setting. Keepthelanding gear in the power off state (pull the landing gear cable out of thecontrol box). After the door and landing gear are set correctly, insert thethree landing gear into the corresponding sockets. If it is foundthat thedirection of the landing gear is wrong, just switch the positiveandnegative poles of the cable (+/-). Mobile APP Settings are the same as Settings box Settings.